Tag: Bushings

Posted on

Brackets in place

What I thought would be an hour’s worth of work this morning turned into 3-1/2 hours, but I’m feeling good about the end result. I went over to tighten up the bolts on the wing root brackets and install the brackets on the outer portion of the wing, for the N struts and landing wires.

Snugging up the bolts at the wing root went fine. They’re not torqued to spec, I’ll torque all of the bolts during the initial assembly and mark them all with Torque-Seal or some other witness marking paint. With those done, I moved on to the other brackets. I found that with the very slight variations in hole locations, some of the brackets needed a hole adjusted slightly to get everything lined up properly. It was also a real bear getting the bushings back into their holes after varnishing. Let’s just say there’s no play there… they’re fitted nice and tight.

In the end, I got all of them installed and everything lines up the way it should. I need to find one more AN4-16A bolt, but I think I may have one at the hangar. Next step, I think, will be to cut and fit the cover plates for the brackets where the fabric will be glued down where the brackets come through.

Posted on

Wing fittings and aileron work

I’ve spent a couple hours this week getting bolt length sorted out and getting some of the wing fittings attached.

My strategy for the wing attach fittings was to make one of each type of fitting, pilot drill the holes with a 1/8″ bit, and use those to mark the location of the holes in the wing spars. Those holes got drilled on a drill press using Forstner bits. Then I cut the rest of the fittings, used the first ones as templates for drilling them, and figured all of the holes should line up.

Well – they’re close. I’m not a machinist, nor am I using tools techniques of suitable precision to produce perfect parts. For example, when looking at the CAW2A wing root mounting brackets, the holes are not perfectly aligned – so there’s a top and bottom to those, meaning until I figured that out it took a few tries to get everything lined up right. No big deal.

Then I discovered that one of the holes isn’t drilled perfectly square. It’s only off by maybe .010 total, but just enough that you can’t run a bolt through the forward bracket, the bushing, and the aft bracket without interference. If the bolts were just going through holes drilled in the wood of the spar, it would be fine – but the bushings are a snug fit, I had to do a little adjusting of that hole to get everything to fit properly.

We finally got the bottom of the aileron leading edge routed so that it’s now in its final state. When fitting the aileron and checking travel, I discovered that I’d messed up just a little when up finishing out the aileron bay. On the first wing, I’d positioned the top beveled strip with the aileron in place, and checking clearance per the plans. On this one, I just measured the first wing and matched it. I don’t have enough up travel on this aileron. After a little more investigation, it’s just the ends that interfere, so easily cleaned up with a couple minutes of work with the razor plane. I’ll need to pay closer attention on the next two wings. I’m thinking just use a length of 1/4″ shim stock to set the spacing with the aileron solidly fixed in its final location.

Posted on

Catching up

I’ve missed a couple of updates to work done on the plane over the past week or so. I got the second coat of varnish on the wing, including the aileron. I got all of the bushings in place, and started to attach the various attaching brackets… oops! No torque wrench. And, I can only find one CAW9 bracket. I think I ran out of 3/16″ x 1″ 2024 flat bar stock before I got them all made; I need to go hunting and gathering again. Once that’s done I can finish off the aileron (the lower leading edge needs a pass through the router for its radius) and move on to varnishing the other wing.

Posted on

A little varnish

Picked up a gallon can of Varathane Ultimate Spar Urethane this afternoon. A gallon can is about the same price as two one-quart cans, and I figure between the wings, fuselage, and tail I’ll probably use most of it. I gave the holes for the bushings and the wood where they will go a coat this afternoon before heading home — it was a busy day cleaning out the garage and ferrying grandkids around. Tomorrow I’ll pick up some primer and hopefully get a start on varnishing the rest of the wing. I’d like to have it assembled and ready to rack by the weekend, if I can. Then I’ll need to pull down the left wing and finish it up – bushings, varnish, brackets.

Posted on

Boy, I’m bushed!

Today I took the wing brackets over to the shop, sorted them all out, and re-marked them so I could tell one part from the other. There are seven (I think) different bracket types. The acid etch solution had removed all of the markings, along with other stuff.

I sorted out which brackets are needed for the right lower wing that’s on the bench, and checked all of the bolt sizes for proper fit. All are acceptable, if not perfect. I have AN4-24A bolts (1-15/16″ grip length) for the main spar root attachment brackets; I could have used AN4-23A (1-13/16″ grip length). It’s not a problem; a couple of AN960 washers do the trick and are a perfectly acceptable solution. On the rear spar N-strut (outer end) brackets, the AN4-16A bolts are a tad long; I could have used -15A. Two AN960 and one AN960L are fine. As a mental exercise I calculated the weight savings if I ordered the shorter bolts. The shorter bolts would weigh about half an ounce less (total per wing); the washers would bring that up to just a smidge over half an ounce — .53 ounce, or about 15 grams per wing. I can live with that.

But I digress. I got all the remaining bushings cut. Once I wrapped my head around that fact that the bushings do not need to be cosmetically and dimensionally perfect, but just need to be “flush or slightly below” the face of the wood per the plans, things went a little quicker. I pulled the 24 tooth per inch metal blade from my bandsaw and replaced it with a 10 TPI wood blade, which is fine for thin wall AL tubing like this. I set up the miter gauge and fence for the length I wanted. The tubing cut-off end was snagging the blade teeth; Stew suggested a spacer on the rip fence that extends just shy of the blade. That did the trick! Now the cut-offs roll out of the way. I cut one piece and tested for fit in the hole; once that was verified I was able to set the fence once and cut as many pieces of each diameter tube as I needed. Easy peasy. That will save hours of build time.

Now I need some etching primer for the brackets, and spar urethane for the wood, and I can get everything installed and call this wing done.

Oh, after I cut the bracket for the aileron connecting rod.

And get the bearing block holes drilled.

And… whatever else I’ve forgotten.

Posted on

More bracketry

Today I got my bag of bolts, washers, and nuts from Aircraft Spruce. Wanting to make sure I had all the correct lengths and all, I headed over to the shop to try them out. As you might guess — especially if you know me — all of the brackets were at home, so no joy there.

I did order a 14 TPI bi-metal bandsaw blade, it should arrive tomorrow. The 24 TPI metal blade is just way too fine for cutting this tubing. Stew says the 10 TPI wood blade I have would do fine — but I want something I can use on the 2024 stock without worry.

Once back at home, I treated all of the brackets with Alumiprep (now known as “Bonderite C-IC33 Aero”). It’s a phosphoric acid etching cleaner, does a bang-up job of cleaning up and etching aluminum parts prior to conversion coating or painting. Well, as it turns out, my Alodine is no good any more. No surprise, really. I left a set of brackets in the bath for an hour and could barely see a tinge of tan or gold color, not enough. Too bad, I was really hoping to use that. I’ll need to pick up some good self-etching primer instead, I’m not spending close to $100 for a quart of Alodine that I’ll then have to dispose of later on.

Posted on

Bushings

On Wednesday I went over and tried cutting some of the bushings used for the bolts that hold the brackets to the wing.

I’ve cut a couple with a chop saw, but one got away and ruined a saw blade and almost took my thumb off. I think I could fix that problem, but after ruining one nice Freud carbide blade I’m not really inclined to pursue that method again. I’ve been using my small (9″) band saw with a metal cutting blade, and it’s been a bit of a struggle. I’ve had no success getting the miter slot aligned to the blade, so I made a custom miter gauge with a slight angle to get straight cuts. I wrapped masking tape around one end and made test cuts until I got a square cut. After cutting, I typically need to take a few thousandths off with sandpaper before I get the correct length.

Until now I’ve been scribing a line with a micrometer and following that with the blade. I think I’m going to switch to clamping a fence down on the table and using that for repeatability. I have three sizes of tubing — 5/8, 1/2, and 3/8 OD. Bushings are made with one, two, or three pieces of tubing nested together, so I need to cut identical length pieces. The 1/2 and 5/8 tubing is a snug enough fit that I can cut them together, but the 3/8 OD is not a snug fit, so I end up having to cut that separately or it spins and moves out of position. I’m going to just try a different approach, as making these bushings is taking forever.

I’ve been using a 1/2″ wide, 24 TPI metal cutting blade on the saw. I think it’s too fine for the AL tubing; I’m going to try a different blade. Of course I’ll have to order it. I have the 24 TPI, as well as 6 and 10 TPI wood cutting blades. I think I want to try 14 TPI.

Posted on

Wing down, new bandsaw blades

Wednesday afternoon I went over and worked with Stu to get the wing down off the rack and onto the bench. I grabbed the nose ribs and, since they weren’t cut out for the false spars, took them home with me. Before I did, I carefully marked where they need to be notched.

Stu has gotten out of the cabinet business and has sold off much of his wood shop equipment. The thickness planer, jointer, band saw, edge banding machine, and some other stuff is gone. Wait — the band saw is gone? Crap, if I’d known I’d have bought it from him on condition that I could leave it where it was. Oh well. I have one at home, a cheap little 10″ tabletop model.

While cutting the notches in the nose ribs, it was immediately apparent that the saw blade was toast. I’d wanted to replace it anyway, as it’s a 1/4″ wide blade and not really great for keeping a straight line. I removed and measured it, then tossed that and the equally worn out metal blade I had for it that couldn’t make it through 1/8″ 6061. I ordered a 62″ x 3/8″ x 6 TPI wood blade, a 10 TPI wood blade, and a 1/2″ wide 24 tooth metal cutting blade.

A few days’ delay was inserted here, while dealing with another issue unrelated to the airplane..

The blades arrived over the past few days. I put the 6-tooth wood cutting blade on and got the saw adjusted’ it works great. I can cut a 1/16 slice off the end of a 2×2. I think I still need to get the saw table squared up a little better with the blade before trying to do any re-sawing, but it’s close enough for the time being. The metal cutting blade slides through that 6061 like butter, so I’ll be able to finish off the AL fittings for the wing and get the tubing cut for the bushings. Then I can order the bolts I need and get the fittings installed.