Tag: Spars

Posted on

Last rib done, first spar started

I just pulled the last two false ribs in the jigs. It’s been a long haul — six and a half years since I built the first rib, but now they’re done AND I’ve got the materials and the place needed to continue the build.

Last night I was over at Stu’s place. One of the main spars has been partially assembled; the spar caps have been glued to the web. I got all of the rest of the parts for the aft face of the spar fitted and ready to glue up. I decided to designate this one the upper right wing. I’ll head over tonight and glue it.

I briefly thought about tearing down the rib jigs now that all of the ribs are finished. I decided not to do that quite yet. For one thing, there’s a chance I may need or want to make more of them for one reason or another. I don’t need two jigs, though. I’ll probably leave the first one I made as is, and pull the blocks and plastic from the second copy. It’s not a high priority, since it will only yield a 4′ x 1′ chunk of MDF.

Posted on

Spar webs

The plans and BOM call for plywood spar webs, cross-cut, 60″ long. The webs are butt-spliced mid-wing, with what seem to me to be fairly narrow blocks of spruce on either side.

Problem is, you can’t buy 60″ wide sheets of aircraft plywood in the US. Aircraft Spruce has ONE size, and not a size I need. Everything else I’ve found is in 48″ wide sheets. And since the web needs to be crosscut, it’s not as simple as just buying a 4′ x 8′ sheet. I’ve contacted Fisher Flying Products as well as another supplier in Canada. Fisher’s tab will be roughly $340, the other place was pretty reasonable for the plywood but wanted over $500 for crating and shipping. To put that in perspective, ACS will sell me the plywood I need for about $100, delivered.

The question is, can I make 48″ long spar webs work in a way that is at least as good, or preferably stonger and better, than the original design? I am no engineer. Especially a mechanical engineer. I’m certainly not qualified to make such a call. Fortunately, I have someone local who is an engineer, and is qualified to help make that decision and recommend another way to do it — if there is one. I’ll be taking the wing plans to the February EAA chapter meeting to go over them with him and see what we can figure out.

If that doesn’t work out, Spruce does sell 5/32 ply in 61″ x 61″ sheets. The spar webs are specified as 1/8″ for the main spar, and 1/16″ for the rear spar. I could just make both webs 5/32 with a slight weight penalty. The plywood would weigh 3 to 5 pounds more, but I’d probably also need to trim 1/32 to 3/32 from the spruce stiffeners, so that might make up for some of it. Again, I’ll need to consult with a real engineer to see if that wold work or not. Ending up with a plane that’s a couple pounds heavier but significantly stronger is OK. Ending up with a plane that is in any way less strong or less safe is absolutely not. And if the ribs need to be modified a little to clear a beefier spar — I’m OK with that.

Posted on

Tempus fugit

Another year draws quickly to a close, with what feels like not a lot of progress on this project. I have a tall stack of ribs, but really nothing else. I had hoped to have a good start on the tail surfaces by now, but haven’t even started on them. We’ll need the basement for a family Christmas party, so no laying a 4×8 sheet of MDF over the island down there to start laminating pine. No worries, though. I have located some nice clear pine boards at Menard’s that will rip down nicely into 10′ long lamination strips. I have an order of Finnish birch ply queued up on Aircraft Spruce’s web site, ready to place the order once I’m sure I have all the stuff on there that’s going to be expensive to ship. As soon as we’re finished with the post-party cleanup, I’ll have the basement available to work in through the rest of the winter since the garage will just be a bit too cold for epoxy.

I also got a great idea from one of the guys on the Biplane Forum. I’ve been pondering how to store the wing ribs. I think I’ll build short pieces of main and rear spars out of pine and non-certified plywood, just to assemble all the ribs and clamp them together. That way I can surface sand them all together, and maybe if I’m lucky use that assembly to run them through the table saw for trimming as well. Maybe.